Differences

This shows you the differences between two versions of the page.

--- en:mobile:user_guide:vaccine [2021/12/24 07:09] – Mark Glover
+++ en:mobile:user_guide:vaccine [2024/02/19 23:47] (current) – [Temperature Breaches] Adam Dewey
@@ Line 39: / Line 39: @@
 Approved sensors can be purchased directly from the manufacturer or reseller online.  Please contact [[coldchain@msupply.foundation]] for further information.
-=== Adding Sensors ===
+==== Adding Sensors ====
 The first time you use the Vaccine module, there will be no sensors connected to your device.
 {{ :en:mobile:user_guide:pasted:20210316-035326.png?600 |}}
@@ Line 51: / Line 51: @@
 We recommend you keep the sensor close when you are adding or editing it within mSupply Mobile.  Also, allow for up to a minute for any changes to be communicated via Bluetooth.
 If you are using a brand new sensor, press the top of the sensor until it flashes to turn it on.
 == Step 1: Select the correct sensor ==
 When you tap **Add Sensor**, your device will scan and list any sensors that can be connected by Bluetooth.
@@ Line 63: / Line 64: @@
   * __Consecutive__ means a single event where the temperature stays over (or under) the threshold for the whole time. So if you have a threshold of 8 degrees, and a consecutive breach time of 10 minutes, then a breach that lasts for 6 minutes, then drops under the threshold for 2 minutes, then breaches again for 6 minutes is __not__ a consecutive breach, but the 2 x 6 minute breaches are added to the cumulative breach records.
   * __Cumulative__ means adding together the total time over a certain temperature for a series of breaches.
 Now we can set the temperature breach conditions for the sensor.  There are four thresholds that you can define:
@@ Line 118: / Line 118: @@
 </WRAP>
+==== Edit Sensor ====
-=== Edit Sensor ===
 To edit sensor details, you can tap on the ‘’cog’’ icon on the mSupply Vaccine home page (above screenshot) or on the Sensor Detail screen.
 Screenshot
@@ Line 133: / Line 131: @@
 </WRAP>
-== Pausing Sensor Downloads ==
+=== Pausing Sensor Downloads ===
 The edit screen also allows you to ''Pause'' temperature logging by the sensor.  When a sensor has been paused, it will appear in the title line both on the mSupply mobile vaccine home screen as well as the Sensor Detail screen.
 {{ :en:mobile:user_guide:pasted:20210316-041408.png?600 |}}
-== Replacing a Sensor ==
+=== Replacing a Sensor ===
 Tapping ''Replace'' will open up the scanner and allow you to choose from list of alternative sensors.  The list will only show sensors that are not currently connected to your device.
 {{ :en:mobile:user_guide:pasted:20210316-041444.png?600 |}}
 From the list, select the replacement sensor.  You can press ''Blink'' to check that you have the correct sensor (the LED light will flash for this sensor).
-== Deleting a Sensor ==
+=== Deleting a Sensor ===
 Tap ''Remove'' to remove any sensor no longer being used. You will receive a prompt to confirm the deletion.
 {{ :en:mobile:user_guide:pasted:20210316-041622.png?600 |}}
@@ Line 237: / Line 235: @@
 TIP: If you change your mind about emailing the data, tap anywhere in the grayed-out area.
 </WRAP>
+=== Temperature Breaches ===
+Temperature breaches are displayed on the graph as warning icons.
+As of February 2024 it is not possible to acknowledge the breaches in mSupply Mobile.
+However, note that this functionality is now available in Open mSupply: See https://docs.msupply.foundation/docs/coldchain/monitoring/#acknowledging-breaches